石膏找平顾名思义就是使用石膏板或是石膏粉与胶调和进行墙面或是天花表面不平整范围的填平工作。这种方法可以进行局部找平且不需要将地面抬高，施工起来比较方便，价格相对来说较为便宜。下面济南石膏粉厂家为您分享：

Gypsum leveling, as the name suggests, refers to the use of gypsum boards or gypsum powder mixed with glue to fill and level the uneven areas of the surface of walls or ceilings. This method can perform local leveling without raising the ground, making construction easier and relatively inexpensive. The following gypsum powder manufacturers in Jinan share with you:

先对墙面进行清理。如果墙面有裂缝、孔洞等情况的话，可以先嵌入石膏粉将它们填补平整。

Clean the wall first. If there are cracks, holes, etc. in the wall, you can first insert gypsum powder to fill them flat.

涂刷界面剂，防止基层开裂。使用滚筒均匀涂刷，阴阳角区域用涂刷满浆，涂刷之后注意保持清洁。

Apply interfacial agent to prevent cracking of the base layer. Use a roller to evenly brush, and the internal and external corner areas are coated with paste. After brushing, pay attention to keeping them clean.

防开裂处理。已经开裂的区域先做修补，使用抹刀开八字缝，用石膏刷清扫粉尘，直接铺贴牛皮纸，涂刷石膏，再使用网格布铺满墙面，使两块布之间搭接严密，重新叠加部分不低于50mm。

Anti cracking treatment. Repair the cracked area first, use a spatula to open the splay joint, use a gypsum brush to clean the dust, directly apply kraft paper, apply gypsum, and then use a grid cloth to cover the wall surface, making sure that the overlap between the two pieces of cloth is tight, and the re overlapping part is not less than 50mm.

接缝处理。不同材质交接处粘贴接缝时，需要粘贴平整牢固。

Joint treatment. When pasting joints at the junction of different materials, it is necessary to paste them smoothly and firmly.

阴阳角弹线。用水平仪在墙面上弹出水平线、垂直线。和顶棚水平线。用石膏粉将边角区域不平整的地方刮平，之后确定墙面大面积平整度的控制线。

Snap the lines at the internal and external corners. Use a spirit level to snap horizontal and vertical lines on the wall. And ceiling level. Use gypsum powder to scrape off uneven areas in the corner areas, and then determine the control line for large area flatness of the wall.

粉刷基层。根据已经标记好的控制线，批刮石膏。将石膏粉与清水按照比例调兑、搅拌均匀，并在规定的时间内使用完。如果批刮的厚度不超过10mm，则需要铺贴一层网格布，之后再批刮一层石膏。

Painting the base layer. According to the marked control line, apply plaster in batches. Mix gypsum powder and clean water in proportion, stir evenly, and use up within the specified time. If the thickness of the batch scraping does not exceed 10mm, it is necessary to lay a layer of grid cloth and then batch scrape a layer of gypsum.

面层施工。基层的石膏层干燥之后，需要在面层涂刷一层石膏，批刮满浆，并找平粗糙的表面，使面层光滑平整。接缝处理。不同材质交接处粘贴接缝时，需要粘贴平整牢固。

Surface layer construction. After the gypsum layer of the base layer is dried, it is necessary to apply a layer of gypsum to the surface layer, scrape the paste thoroughly, and level the rough surface to make the surface layer smooth and smooth. Joint treatment. When pasting joints at the junction of different materials, it is necessary to paste them smoothly and firmly.

以上就是关于石膏粉局部找平的分享了，每一个工地都是认真负责，干净整洁。我们一直以来对工地的每一项进度都是严格把控的，做到一丝不苟。想要了解更多工艺的，继续关注我们https://www.jnfhjc.com。

The above is the sharing of partial leveling of gypsum powder. Every construction site is conscientious, responsible, and clean. "We have always strictly controlled every progress on the construction site, and are meticulous.". For those who want to learn more about the process, continue to follow us https://www.jnfhjc.com 。